AUTOMATIC POOL COVER MOTORS MANUAL
AUTOMATIC POOL COVER MOTORS FREE

Most automatic pool covers have shear pins built in to prevent more costly damage to the motor and ropes.

This is located in a hole drilled through the motor shaft and the cover engagement cams. If you attempt to roll back the cover with too much leaf or water weight on top, or if the cover is hanging up at some spot from maladjustment, you may hear a loud pop which is likely the cover shear pin breaking. It may be good medicine to treat the cover annually with a vinyl conditioner to protect against staining and fading. Similarly, use a cover pump to remove most of the water before rolling back the cover. If the cover is inundated with leaves and/or water, use a leaf rake on the telescopic pole, scooping out as many leaves as possible before rolling the cover back. When you get to the last panel, pump off the water with a cover pump and scoop out the leaves with a leaf rake. Roll the cover up one panel at a time, cleaning in this manner.

Standing at the reel end, use a blower or a garden hose and a pool brush on a telescopic pole to push debris towards the shallow end. We recommend cleaning an auto cover by panel segments. This is usually easier than cleaning the pool, however.īelow are some troubleshooting tips for automatic pool covers, from our help file.

AUTOMATIC POOL COVER MOTORS FREE

Auto covers have also been attributed to drowning prevention (although the solid cover must have rain water pumped off with an automatic cover pump to be considered safe).Īn auto cover will keep your pool free from leaves and wind-blown debris however, you'll have to clean off the cover before opening it. Even the Department of Energy has a home page devoted to the economic benefits of pool covers. For freeform pools, there is the option of going trackless, with the cover being locked down around the edge with tiny plastic anchors.Īutomatic cover manufacturers boast of water, chemical, electrical and heat savings.

AUTOMATIC POOL COVER MOTORS MANUAL

Less expensive models are manual and pull open by a hand crank, and close by pulling a rope. The slats can be custom cut to accommodate wall curves, overhanging rock waterfalls or spas, and can be designed with several covers of different sizes to accommodate nearly any pool shape. The large leading edge, a steel tube that runs across the pool is now available in a low profile design that hides easily.Ī newer style of automatic pool cover, dubbed by some to be a European Slat Design, uses vinyl or PVC air filled slats that float on the water and use no track. Tracks can be hidden by cantilevered deck sections. No longer do we have to run track down both sides of the pool. They can, however, be retrofitted to almost any shape pool. The roller can be housed in a box built at the deep end of the pool, level with the pool deck, or the roller can be housed in a box on top of the pool deck.Īutomatic covers look and perform somewhat better when installed on a rectangle pool at the time of construction. The motor that powers the reel to cover and uncover the pool is usually electric, however a hydraulic motor can be used (powered by an external electric motor), which has some advantage in terms of reliability, especially when the roller or reel is located in a deck box and is subject to moisture. One end of the roller is attached to an electric motor, which is wired to a two direction switch (open or closed). An aluminum roller on one end of the pool houses the cover and the tension rope when the cover is open. In the traditional automatic pool cover, a reinforced vinyl fabric runs between tracks on either side of the pool's length. Having an automatic pool cover is an additional layer of protection around a pool – like a horizontal fence! From hand crank models to fully electronic, key-operated systems, today's automatic covers are more reliable, durable, and safer than ever before. All of the equipment included with our kits is top-of-the-line and is built to last.The automatic pool cover has come a long way in recent years. In addition, Pool Warehouse doesn’t sell cheap “Economy” pool kits that are missing essential parts that you will ultimately need to buy later or that come with substandard equipment that will need to be upgraded soon after installation.

We take pride in using only American-made pool walls every wall panel (steel or polymer) and every pool liner are manufactured by craftsmen right here in the USA. Check out customer videos at the bottom of this page for visuals on how this pool kit might look in your backyard! These kits include the APC 365 Automatic Swimming Pool Cover and are perfect for those wanting extra security around their pool! This type of automatic cover is mounted under the pool coping and recesses into the included storage box, located under the deck.

Automatic pool cover motors